| We hope you enjoy your visit. You're currently viewing our forum as a guest. This means you are limited to certain areas of the board and there are some features you can't use. If you join our community, you'll be able to access member-only sections, and use many member-only features such as customizing your profile, sending personal messages, and voting in polls. Registration is simple, fast, and completely free. When you register for an account you will see the following message -Due to the amount of "spammers" trying to get on the board all registrations must be approved by me. What this means is that after you register your registration must be authorized. Also your email address has to be verified, you will receive an email with a link YOU MUST CLICK ON THIS LINK TO VERIFY YOUR EMAIL OR YOUR ACCOUNT WILL NOT BE APPROVED. I check the message board several times a day and approve registrations as they come in. Sorry for the wait but it is necessary to keep the spam off the boards.Thanks,Koz It is very important that you click on the link in the email to validate your email. Please check your spam folder as the email message may be sent there by your email provider. IF YOU DO NOT CLICK ON THIS LINK YOUR ACCOUNT WILL NOT BE APPROVED !!! Join our community! If you're already a member please log in to your account to access all of our features: |
| Arrowhead Drag; Sidehilling with an ArrowHead Drag | |
|---|---|
| Tweet Topic Started: Dec 25 2012, 09:40 PM (1,167 Views) | |
| mtnmaxman600 | Dec 25 2012, 09:40 PM Post #1 |
|
Advanced Operator
![]() ![]() ![]() ![]() ![]()
|
What the best way to keep and arrowhead drag following behind the groomer on the hill sides? |
![]() |
|
| Sledderglen | Dec 25 2012, 10:12 PM Post #2 |
|
Advanced Operator
![]() ![]() ![]() ![]() ![]()
|
We added pizza cutters to our 5x9.5 drag. 14" Coulters from a John Deere air seeder on a hub bearing assembly . Can raise and lower them for when not needed. Works very good |
![]() |
|
| firecat | Dec 26 2012, 07:50 AM Post #3 |
|
Advanced Operator
![]() ![]() ![]() ![]() ![]()
|
We have a Sno-Boss drag , which is almost identical to an Arrowhead. I have learned to lower the rear tires so that they touch the ground. This will keep it from sliding sideways. After a little practice , you will find how much to lower them. You should also make sure your side guide plates or "rudders" are hanging down below the side plates of your drag to where you want them. I've found if you have these hanging down too far , and you are not in real deep snow , you won't get a good "finish" because the pan is actually held up off the snow because of the guides.
|
![]() |
|
| St. Louis Dave | Dec 28 2012, 02:19 PM Post #4 |
|
Advanced Operator
![]() ![]() ![]() ![]() ![]()
|
Yes on all of the above. The rear wheel trick works very well. |
|
Case MXU 130 John Deere 7720 Arrowhead Drags Polaris 800 XCR Polaris 800 XC Trailriders Snowmobile Club - Baldwin, Michigan Groomer Operator www.baldwinsnowmobiling.com Club Alloutes - Dubreuilville, ON Groomer Operator Volunteer of the year 2007 | |
![]() |
|
| trailboss77 | Dec 28 2012, 09:16 PM Post #5 |
|
Advanced Operator
![]() ![]() ![]() ![]() ![]()
|
The wheel trick works well with a Sno-Boss drag but not so good with the Arrowhead. Arrowhead drags have wider tires and with 4 of them on the back it still likes to slide. |
|
Have been grooming since 1978 have covered more than 100,000 miles of snowmobile trail. | |
![]() |
|
| RJ85MSP | Dec 29 2012, 06:09 PM Post #6 |
|
Advanced Operator
![]() ![]() ![]() ![]() ![]()
|
Well nothing is the absolute solution for this drag. Longer skegs, pizza cutters etc help but only marginally. Wheels down act ok but leave wheel prints ruts in the snow. The only solution is to have more skegs such as what you see on the mogul master drag or maxi drag. These styles use 5 skegs of adjustable height to control this. We had arrowhead and while it groomed ok, we were always dissapointed in the way it tracked. It's just the design, it needs more than pizza cutters that's for sure. |
![]() |
|
| xcspxlt | Dec 31 2012, 09:58 AM Post #7 |
|
Advanced Operator
![]() ![]() ![]() ![]() ![]()
|
Our older Ultra only has single wheels in the back and one set of rudders. I see the newer Ultras now have rudders on the outside also. We weleded a 1" square stock to the bottome of our side rails. Like wear bars on a ski. This helped some but only if you you have the drag full of snow and flat on the ground. Lift the front at all and it still wants to slde. We do a lot of ditches that are not flat, and I have found having more snow int he drag helps MOST of the time. |
| XCSPXLT | |
![]() |
|
| 1 user reading this topic (1 Guest and 0 Anonymous) | |
| « Previous Topic · General Discussion · Next Topic » |





![]](http://z1.ifrm.com/static/1/pip_r.png)



5:00 AM Jul 11